test

The tracking issue for this feature is: None.


The internals of the test crate are unstable, behind the test flag. The most widely used part of the test crate are benchmark tests, which can test the performance of your code. Let's make our src/lib.rs look like this (comments elided):


#![allow(unused)]
#![feature(test)]

fn main() {
extern crate test;

pub fn add_two(a: i32) -> i32 {
    a + 2
}

#[cfg(test)]
mod tests {
    use super::*;
    use test::Bencher;

    #[test]
    fn it_works() {
        assert_eq!(4, add_two(2));
    }

    #[bench]
    fn bench_add_two(b: &mut Bencher) {
        b.iter(|| add_two(2));
    }
}
}

Note the test feature gate, which enables this unstable feature.

We've imported the test crate, which contains our benchmarking support. We have a new function as well, with the bench attribute. Unlike regular tests, which take no arguments, benchmark tests take a &mut Bencher. This Bencher provides an iter method, which takes a closure. This closure contains the code we'd like to benchmark.

We can run benchmark tests with cargo bench:

$ cargo bench
   Compiling adder v0.0.1 (file:///home/steve/tmp/adder)
     Running target/release/adder-91b3e234d4ed382a

running 2 tests
test tests::it_works ... ignored
test tests::bench_add_two ... bench:         1 ns/iter (+/- 0)

test result: ok. 0 passed; 0 failed; 1 ignored; 1 measured

Our non-benchmark test was ignored. You may have noticed that cargo bench takes a bit longer than cargo test. This is because Rust runs our benchmark a number of times, and then takes the average. Because we're doing so little work in this example, we have a 1 ns/iter (+/- 0), but this would show the variance if there was one.

Advice on writing benchmarks:

  • Move setup code outside the iter loop; only put the part you want to measure inside
  • Make the code do "the same thing" on each iteration; do not accumulate or change state
  • Make the outer function idempotent too; the benchmark runner is likely to run it many times
  • Make the inner iter loop short and fast so benchmark runs are fast and the calibrator can adjust the run-length at fine resolution
  • Make the code in the iter loop do something simple, to assist in pinpointing performance improvements (or regressions)

Gotcha: optimizations

There's another tricky part to writing benchmarks: benchmarks compiled with optimizations activated can be dramatically changed by the optimizer so that the benchmark is no longer benchmarking what one expects. For example, the compiler might recognize that some calculation has no external effects and remove it entirely.


#![allow(unused)]
#![feature(test)]

fn main() {
extern crate test;
use test::Bencher;

#[bench]
fn bench_xor_1000_ints(b: &mut Bencher) {
    b.iter(|| {
        (0..1000).fold(0, |old, new| old ^ new);
    });
}
}

gives the following results

running 1 test
test bench_xor_1000_ints ... bench:         0 ns/iter (+/- 0)

test result: ok. 0 passed; 0 failed; 0 ignored; 1 measured

The benchmarking runner offers two ways to avoid this. Either, the closure that the iter method receives can return an arbitrary value which forces the optimizer to consider the result used and ensures it cannot remove the computation entirely. This could be done for the example above by adjusting the b.iter call to


#![allow(unused)]
fn main() {
struct X;
impl X { fn iter<T, F>(&self, _: F) where F: FnMut() -> T {} } let b = X;
b.iter(|| {
    // Note lack of `;` (could also use an explicit `return`).
    (0..1000).fold(0, |old, new| old ^ new)
});
}

Or, the other option is to call the generic test::black_box function, which is an opaque "black box" to the optimizer and so forces it to consider any argument as used.

#![feature(test)]

extern crate test;

fn main() {
struct X;
impl X { fn iter<T, F>(&self, _: F) where F: FnMut() -> T {} } let b = X;
b.iter(|| {
    let n = test::black_box(1000);

    (0..n).fold(0, |a, b| a ^ b)
})
}

Neither of these read or modify the value, and are very cheap for small values. Larger values can be passed indirectly to reduce overhead (e.g. black_box(&huge_struct)).

Performing either of the above changes gives the following benchmarking results

running 1 test
test bench_xor_1000_ints ... bench:       131 ns/iter (+/- 3)

test result: ok. 0 passed; 0 failed; 0 ignored; 1 measured

However, the optimizer can still modify a testcase in an undesirable manner even when using either of the above.