% Boisik Logo Roman 10 point (contains logo_i) if unknown bskbase: input bskbase fi font_identifier:="BSKRLOGO"; font_size 10pt#; u#:=20/36pt#; % unit width width_adj#:=0pt#; % width adjustment for certain characters serif_fit#:=0pt#; % extra sidebar near lowercase serifs cap_serif_fit#:=5/36pt#; % extra sidebar near uppercase serifs letter_fit#:=0pt#; % extra space added to all sidebars body_height#:=270/36pt#; % height of tallest characters asc_height#:=255/36pt#; % height of lowercase ascenders cap_height#:=246/36pt#; % height of caps fig_height#:=240/36pt#; % height of numerals x_height#:=159/36pt#; % height of lowercase without ascenders math_axis#:=95/36pt#; % axis of symmetry for math symbols bar_height#:=100/36pt#; % height of crossbar in lowercase e comma_depth#:=70/36pt#; % depth of comma below baseline desc_depth#:=115/36pt#; % depth of lowercase descenders com_height#:=135/36pt#; %height of B bar crisp#:=0pt#; % diameter of serif corners tiny#:=8/36pt#; % diameter of rounded corners fine#:=7/36pt#; % diameter of sharply rounded corners thin_join#:=7/36pt#; % width of extrafine details hair#:=10/36pt#; % lowercase hairline breadth stem#:=24/36pt#; % lowercase stem breadth curve#:=27/36pt#; % lowercase curve breadth like_hair#:=12/36pt#; like_stem#:=30/36pt#; like_curve#:=38/36pt#; ess#:=32/36pt#; % breadth in middle of lowercase s flare#:=33/36pt#; % diameter of bulbs or breadth of terminals dot_size#:=30/36pt#; % diameter of dots cap_hair#:=12/36pt#; % uppercase hairline breadth alt_cap_hair#:=16/36pt#; % alternative uppercase hairline breadth cap_stem#:=30/36pt#; % uppercase stem breadth cap_curve#:=34/36pt#; % uppercase curve breadth like_cap_hair#:=14/36pt#; like_cap_stem#:=38/36pt#; like_cap_curve#:=46/36pt#; cap_ess#:=39/36pt#; % breadth in middle of uppercase s rule_thickness#:=.4pt#; % thickness of lines in math symbols jut#:=25/36pt#; % protrusion of lowercase serifs cap_jut#:=30/36pt#; % protrusion of uppercase serifs beak_jut#:=10/36pt#; % horizontal protrusion of beak serifs beak#:=80/36pt#; % vertical protrusion of beak serifs vair#:=10/36pt#; % vertical diameter of hairlines notch_cut#:=10pt#; % maximum breadth above or below notches bar#:=11/36pt#; % lowercase bar thickness slab#:=11/36pt#; % serif and arm thickness cap_bar#:=11/36pt#; % uppercase bar thickness cap_band#:=11/36pt#; % uppercase thickness above/below lobes cap_notch_cut#:=10pt#; % max breadth above/below uppercase notches serif_drop#:=15/36pt#; % vertical drop of sloped serifs stem_corr#:=1/36pt#; % for small refinements of stem breadth vair_corr#:=1/36pt#; % for small refinements of hairline height apex_corr#:=0pt#; % extra width at diagonal junctions punct_fit#:=1pt#; drop_stem#:=0/36pt#; ser_boule#:=0/36pt#; o#:=4/36pt#; % amount of overshoot for curves apex_o#:=8/36pt#; % amount of overshoot for diagonal junctions slant:=0; % tilt ratio $(\Delta x/\Delta y)$ fudge:=1; % factor applied to weights of heavy characters math_spread:=0; % extra openness of math symbols superness:=1/sqrt2; % parameter for superellipses superpull:=1/6; % extra openness inside bowls beak_darkness:=11/30; % fraction of triangle inside beak serifs ligs:=2; % level of ligatures to be included medieval:=true; %medieval numerals monofig:=false; %should numerals have fixed width bulbes:=false; square_dots:=false; % should dots be square? hefty:=false; % should we try hard not to be overweight? serifs:=true; % should serifs and bulbs be attached? monospace:=false; % should all characters have the same width? variant_g:=false; % should an italic-style g be used? low_asterisk:=false; % should the asterisk be centered at the axis? math_fitting:=false; % should math-mode spacing be used? chars.logo_i:=oct"203"; generate bskroman % switch to the driver file
Generated by dwww version 1.15 on Thu May 23 19:14:57 CEST 2024.