dwww Home | Show directory contents | Find package

Copyright (c) 2004-2005 The Trustees of Indiana University and Indiana
                        University Research and Technology
                        Corporation.  All rights reserved.
Copyright (c) 2004-2005 The University of Tennessee and The University
                        of Tennessee Research Foundation.  All rights
                        reserved.
Copyright (c) 2004-2005 High Performance Computing Center Stuttgart,
                        University of Stuttgart.  All rights reserved.
Copyright (c) 2004-2005 The Regents of the University of California.
                        All rights reserved.
Copyright (c) 2008-2020 Cisco Systems, Inc.  All rights reserved
Copyright (c) 2013-2020 Intel, Inc.  All rights reserved.
$COPYRIGHT$

Additional copyrights may follow

$HEADER$

Overview
========

This file is here for those who are building/exploring PMIx in its
source code form, most likely through a developer's tree (i.e., a Git
checkout).


Debugging vs. Optimized Builds
==============================

**If you are building PMIx from a Git checkout**, the default build
includes a lot of debugging features.  This happens automatically when
when configure detects the hidden ".git" Git meta directory (that is
present in all Git checkouts) in your source tree, and therefore
activates a number of developer-only debugging features in the PMIx
code base.

By definition, debugging builds will perform [much] slower than
optimized builds of PMIx.  You should *NOT* conduct timing tests
or try to run production performance numbers with debugging builds.

**REMEMBER** that you need to add appropriate -O directives
to your CFLAGS so your compiler will optimize the code! Otherwise,
while we will have disabled various debug code paths, the resulting
binary will not have been optimized.

NOTE: this version of PMIx requires the Libevent package to build
and operate. Any version of Libevent greater than or equal to
2.0.21 is acceptable. It optionally supports the HWLOC package
for providing topology information to both the host environment
(by collecting local inventory for rollup) and local client
processes. Any version of HWLOC greater than 1.10 is supported,
although versions in the 2.x series are recommended.

If you wish to build an optimized version of PMIx from a
developer's checkout, you have a couple of options:

1. Manually specify configure options to disable the debugging
   option.  You'll need to carefully examine the output of
   "./configure --help" to see which options to disable.
   They are all listed, but some are less obvious than others (they
   are not listed here because it is a changing set of flags; by
   Murphy's Law, listing them here will pretty much guarantee that
   this file will get out of date):

     shell$ ./autogen.pl
     shell$ ./configure --disable-debug ...
     [...lots of output...]
     shell$ make all install

2. Use a VPATH build.  Simply build PMIx from a different
   directory than the source tree -- one where the .git subdirectory
   is not present.  For example:

     shell$ git clone https://github.com/openpmix/openpmix.git pmix
     shell$ cd pmix
     shell$ ./autogen.pl
     shell$ mkdir build
     shell$ cd build
     shell$ ../configure ...
     [...lots of output...]
     shell$ make all install

Note that in both cases you must point configure at the libevent
installation using the --with-libevent=<dir> option if it is in
a non-standard location. Similarly, non-standard locations for
the HWLOC package must be specified using the --with-hwloc=<dir>
option. In both cases, PMIx will automatically detect these
packages in standard locations and built-in support for them
unless otherwise specified using the respective configure option.


Use of GNU Autoconf, Automake, and Libtool (and m4)
===================================================

This procedure is *ONLY* necessary if you are building from a
developer's tree.  If you have a PMIx distribution tarball, this
procedure is unnecessary -- you can (and should) skip reading this
section.

If you are building PMIx from a developer's tree, you must first
install fairly recent versions of the GNU tools Autoconf, Automake,
and Libtool (and possibly GNU m4, because recent versions of Autoconf
have specific GNU m4 version requirements).  The specific versions
required depend on if you are using the master or a release branch (and
which release branch you are using).  The specific versions can be
found at:

    https://pmix.org/code/getting-the-reference-implementation/

You can check what versions of the autotools you have installed with
the following:

shell$ m4 --version
shell$ autoconf --version
shell$ automake --version
shell$ libtoolize --version

To strengthen the above point: the core PMIx developers typically
use very, very recent versions of the GNU tools.  There are known bugs
in older versions of the GNU tools that PMIx no longer compensates
for (it seemed senseless to indefinitely support patches for ancient
versions of Autoconf, for example).  You *WILL* have problems if you
do not use recent versions of the GNU tools.

If you need newer versions, you are *strongly* encouraged to heed the
following advice:

NOTE: On MacOS/X, the default "libtool" program is different than the
      GNU libtool.  You must download and install the GNU version
      (e.g., via MacPorts, Homebrew, or some other mechanism).

1. Unless your OS distribution has easy-to-use binary installations,
   the sources can be can be downloaded from:

        ftp://ftp.gnu.org/gnu/autoconf/
        ftp://ftp.gnu.org/gnu/automake/
        ftp://ftp.gnu.org/gnu/libtool/
        and if you need it:
        ftp://ftp.gnu.org/gnu/m4/

   NOTE: It is certainly easiest to download/build/install all four of
   these tools together.  But note that PMIx has no specific m4
   requirements; it is only listed here because Autoconf requires
   minimum versions of GNU m4.  Hence, you may or may not *need* to
   actually install a new version of GNU m4.  That being said, if you
   are confused or don't know, just install the latest GNU m4 with the
   rest of the GNU Autotools and everything will work out fine.

2. Build and install the tools in the following order:

   2a. m4
   2b. Autoconf
   2c. Automake
   2d. Libtool

3. You MUST install the last three tools (Autoconf, Automake, Libtool)
   into the same prefix directory.  These three tools are somewhat
   inter-related, and if they're going to be used together, they MUST
   share a common installation prefix.

   You can install m4 anywhere as long as it can be found in the path;
   it may be convenient to install it in the same prefix as the other
   three.  Or you can use any recent-enough m4 that is in your path.

   3a. It is *strongly* encouraged that you do not install your new
       versions over the OS-installed versions.  This could cause
       other things on your system to break.  Instead, install into
       $HOME/local, or /usr/local, or wherever else you tend to
       install "local" kinds of software.
   3b. In doing so, be sure to prefix your $path with the directory
       where they are installed.  For example, if you install into
       $HOME/local, you may want to edit your shell startup file
       (.bashrc, .cshrc, .tcshrc, etc.) to have something like:

          # For bash/sh:
          export PATH=$HOME/local/bin:$PATH
          # For csh/tcsh:
          set path = ($HOME/local/bin $path)

   3c. Ensure to set your $path *BEFORE* you configure/build/install
       the four packages.

4. All four packages require two simple commands to build and
   install (where PREFIX is the prefix discussed in 3, above).

      shell$ cd m4-1.4.13
      shell$ ./configure --prefix=PREFIX
      shell$ make; make install

      --> If you are using the csh or tcsh shells, be sure to run the
          "rehash" command after you install each package.

      shell$ cd ../autoconf-2.68
      shell$ ./configure --prefix=PREFIX
      shell$ make; make install

      --> If you are using the csh or tcsh shells, be sure to run the
          "rehash" command after you install each package.

      shell$ cd ../automake-1.11.1
      shell$ ./configure --prefix=PREFIX
      shell$ make; make install

      --> If you are using the csh or tcsh shells, be sure to run the
          "rehash" command after you install each package.

      shell$ cd ../libtool-2.2.8
      shell$ ./configure --prefix=PREFIX
      shell$ make; make install

      --> If you are using the csh or tcsh shells, be sure to run the
          "rehash" command after you install each package.

   m4, Autoconf and Automake build and install very quickly; Libtool will
   take a minute or two.

5. You can now run PMIx’s top-level "autogen.pl" script.  This script
   will invoke the GNU Autoconf, Automake, and Libtool commands in the
   proper order and setup to run PMIx's top-level "configure" script.

   5a. You generally need to run autogen.pl only when the top-level
       file "configure.ac" changes, or any files in the config/ or
       <project>/config/ directories change (these directories are
       where a lot of "include" files for PMI’xs configure script
       live).

   5b. You do *NOT* need to re-run autogen.pl if you modify a
       Makefile.am.

Use of Flex
===========

Flex may be used during the compilation of a developer's checkout (it is
not used to build official distribution tarballs).  Other flavors of
lex are *not* supported: given the choice of making parsing code
portable between all flavors of lex and doing more interesting work on
PMIx, we greatly prefer the latter.

Note that no testing has been performed to see what the minimum
version of Flex is required by PMIx.  We suggest that you use
v2.5.35 at the earliest.

Note that the flex-generated code generates some compiler warnings on
some platforms, but the warnings do not seem to be consistent or
uniform on all platforms, compilers, and flex versions.  As such, we
have done little to try to remove those warnings.

If you do not have Flex installed, it can be downloaded from the
following URL:

    https://github.com/westes/flex

Use of Pandoc
=============

Similar to prior sections, you need to read/care about this section
*ONLY* if you are building from a developer's tree (i.e., a Git clone
of the Open MPI source tree).  If you have an Open MPI distribution
tarball, the contents of this section are optional -- you can (and
probably should) skip reading this section.

The Pandoc tool is used to generate Open MPI's man pages.
Specifically: Open MPI's man pages are written in Markdown; Pandoc is
the tool that converts that Markdown to nroff (i.e., the format of man
pages).

You must have Pandoc >=v1.12 when building Open MPI from a developer's
tree.  If configure cannot find Pandoc >=v1.12, it will abort.

If you need to install Pandoc, check your operating system-provided
packages (to include MacOS Homebrew and MacPorts).  The Pandoc project
itself also offers binaries for their releases:

    https://pandoc.org/

Generated by dwww version 1.15 on Sat Jun 15 20:31:28 CEST 2024.