README for USB_ModeSwitch Data Almost all new and corrected device configurations since around 2012 were collected and compiled by Lars Melin. Thank you! Without a well-maintained base of configuration info, usb_modeswitch would just be a useless blob of code. So: PLEASE REPORT NEW DEVICES ! For up-to-date and detailed information (plus a friendly forum) visit http://www.draisberghof.de/usb_modeswitch This is a data package to complement the full release package of USB_ModeSwitch, a tool to switch multi-mode USB devices. It is used since usb-modeswitch version 1.0.3. Recommended version of usb-modeswitch package is 2.4.0 and above. Installation ============ Just run "make install". To re-generate udev rules file (Note: "tcl" package required), type "make clean" and install again . Tasks initiated by the rules file: ================================== - call tiny shell script in /lib/udev which in turn calls the wrapper (/usr/sbin/usb_modeswitch_dispatcher) to initiate switching for known devices when plugged in or present at boot time - adding symlink "gsmmodem" to appropriate connection port (out of 2-5 ports provided by some devices); this is only a convenience feature and NOT needed for switching or later port operation. This action will be triggered for known modems only (at least switched once before on this system) Explanation about config file names: ==================================== Names consist of <VendorID>:<ProductID>, respective to the default device mode. Should more detailed identification become necessary, one or more attributes to test can be attached after further colons: <VendorID>:<ProductID>:<Attribute>=<String>[:<Attribute>=<String> ...] The strings match if they are part of the attribute content. Use "_" to match spaces (it will match "_" too!). Currently recognized attributes are: uMa = USB, iManufacturer uPr = USB, iProduct uSe = USB, iSerial sVe = SCSI, Vendor sMo = SCSI, Model sRe = SCSI, Revision This list is easily extendable should it be necessary. Example: <vid>:<pid>:uPr=CDMA_Mo will match iProduct "CDMA Modem" or "MyCDMA_Mordor" Generic config files (per vendor ID): ===================================== Introduced in program package 2.2.0, this feature allows config files with a name in the form <idVendor>:#<system flavour>. The default flavour is "linux". The system parameter is taken from "/proc/version". The main use currently is a sort of OS switch to treat all Huawei devices differently on Android. There is no guarantee though that the /proc/version information will always point to Android, so this method may change in future versions. Annother form of usage is a fallback if the device ID is yet unknown. For Huawei devices, the switching method is uniform and not likely to change, so it is possible to provide a generic configuration. Example file names: "12d1:#android" and "12d1:#linux" Note that these files have to be created explicitely on demand. Their default inclusion has led to unwanted switching attempts with unrelated devices like phones. Parameters used only in config files: ===================================== These are not evaluated by the binary but by the wrapper. - WaitBefore=<seconds> delay the switching process See also complete parameter explanation in REFERENCE. Notes about specific devices: ============================= - Huawei devices have a generic entry in the rules file; also there are generic config files for these devices (Linux/Android) as fall-back or as OS-specific mode control. This was suggested and approved by the manufacturer - 1266:1000 (Royaltek Q110): switching method very likely but unconfirmed - 05c6:2000 (unnamed HSDPA modem from "dealextreme"): unusually long switching time reported, even with MS Windoze - 30 to 40 seconds. Don't be alarmed. - 0471:1210 (Philips chipset): had to be split after variants with different targets and behaviour appeared. This is not fully confirmed yet, please report problems. - 1004:6190 (LG AD600): seems to require an unusually wait before starting the modeswitch (10 secs) Legal ===== This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details: http://www.gnu.org/licenses/gpl.txt Or find it as the file COPYING in this folder. Last revised: 2017-02-05, Josua Dietze
Generated by dwww version 1.15 on Sun Jun 16 20:29:47 CEST 2024.